Front stack done… filled last night with lots of pots of all sizes & styles. Can’t wait to see them when they’re fired!!! Time to brick the door…


Gary Jackson: Fire When Ready Pottery
A Chicago potter’s somewhat slanted view of clay & play |
Front stack done… filled last night with lots of pots of all sizes & styles. Can’t wait to see them when they’re fired!!! Time to brick the door…



Back stack loaded last night… pretty tight to the arched roof… nice!!!


An empty soda kiln full of potential. Just getting ready for the start of my three-day SODA-FIRING WORKSHOP at Lillstreet Art Center. Tonight we’ll learn about soda-firing, glaze, wad & load this kiln. Tomorrow we fire and then they come back next week to unload and find their treasures!

So I’ve wiped off the drips from the liner glazes & cleaned the rims of the mugs. Next I’ll add some wadding to the bottoms and they’ll be ready for loading into the soda kiln… my “Plan B” in case my Soda-Firing Workshop students don’t have enough work to fill the kiln tonight when we load in class later tonight. If these don’t make it in… there’s always my next soda kiln… one step ahead…

So Ive been working on some more of my “handbuilt-wheeltrown-combo” mugs. The bottoms are wheelthrown, the sides handbuilt, and then trimmed & refined on the wheel again! One of my favorite “tricks” for making fun textured mugs!
I start by making some textured slabs of clay. Sometimes with my own stamps, texture mats, or carved rolling pins… like this great one from STODOLA!!! They make tons of different rolling pin textures… including custom designs if you need that. Check ’em out at www.stodola.org.


After pressing in a texture, I cut them into straight-sided rectangles… long enough to be the circumference around the base of the cup.

I throw little “bases” on the wheel… just a small little disc wheelthrown on a plastic bat. I do NOT wire them off as I will be putting them back on the wheel to continue to the process and I want them to stay centered.

I start assembling them by wrapping the slab around the base – scoring & slipping along the way. One of the benefits of this technique is that the weight of the slab is supported by resting on the plastic bat. The extra part below the wheelthrown bottom will be trimmed off later. But it makes a great support system at this point.
Where the slab overlaps, I cut it on an angle and then connect that seam… trying to blend it together as best I can without ruining the pattern. A good “secure” seam is pretty important here.



After attaching the sides, you can spin them on the wheel and press outwards from the inside to give the cup a little curve & volume. I also give the rim a little extra attention to keep it round & smooth… like a wheelthrown cup.








I let the cylinders set-up overnight before trimming… under plastic so they dry slowly to leatherhard. At this point, they can be wired off the plastic bat.
I start by cutting off the excess slab that is “under” where the slab attaches to the wheelthrown disc with a sharp blade. Confusing a bit… as it is now “above” the connection point as the cup has been flipped for trimming.



Then I start trimming the bottom as though it were a “normal” wheelthrown cup. The Giffin Grip helps hold everything in place and centers things quickly! And my DiamondCore Trimming Tools work great for trimming a clan, crisp footring. I make sure to trim all the way into the textured slab so that it blends together and looks seamless.


Once trimmed, I let them sit under plastic while I pull some handles for them. Cups are cups… but a mug needs a handle!!!

So when the handles stiffen-up a bit, I start attaching them to the sides… usually where the seam is as a little “creative camouflage.”












I let the mugs sit under plastic overnight again so that they stiffen-up to leatherhard and the moisture levels balance out. Since these are going to be soda-fired, I decided to dip them in thin colored flashing slips. I held them by the footring and carefully submerged them into the slip to only cover the textured slab sides. I left the curved wheelthrown bottoms as raw clay. I think that the difference will look cool after soda-firing! As the slip was dripping wet after dipping, I propped them up on kiln posts so the dripping would stop before flipping them back over. I didn’t want big drippy runs going down the sides.


So now they’re drying and getting ready for a bisque firing. Once fired, I will add a liner glaze and maybe some other colored glaze accents. After soda-firing, the textures should pop nicely and the flashing slips will help accentuate the pattern.
Finger crossed.
Love the morning sun shining in on Allison’s mug… looks like Spring sunshine to me!!! This is one of my “wheelthrown-handbulit-combo” mugs… which I’m in the process of making more of right now!!! Thanks for sharing your morning ritual with us Allison!

Well, it’s another Monday, so I guess it’s time for another Mugshot… or eight?! Just a few more mugs hanging out on my back porch on a Monday afternoon!








Celebrating NATIONAL TILE DAY with a quick glimpse of the tiled wall I made for my condo! Sure, it may be one of little known holidays… but still a fun “reason” to show-off my tiled wall. Usually just those folks who come to my Holiday Home Show gets to see it. There are just short of three thousand handmade soda-fired tiles on the wall… 2,894 for the record… with textures, patterns and a few hidden surprises!
So here’s a quick game for you…
Can you fund my initials in the mix of tiles?
As you scroll down it will get easier, so don’t cheat!




Looks like someone found the perfect napkin holder… employing one of my stamped & soda-fired oval vases with the perfect fit!

Following up with a little post-shovel “warm-me-up†cup of hot chocolate… complete with the requisite JUMBO MARSHMALLOW!!!
See?… I knew I liked shoveling for some strange reason!!!



|
Gary Jackson: Fire When Ready Pottery
Lillstreet Studios ∙ 4401 North Ravenswood, Chicago, Illinois 60640 ∙ 773-307-8664 gary@firewhenreadypottery.com |