While I’m firing the soda kiln today, it’s a good chance to get some work done in the studio like glazing, cleaning & re-organizing! Glazing is always my least favorite part of the process… but it’s got to get done at some point. And since I’m “trapped” here all day firing, today might just be the day to tackle glazing these new berry bowls!

So I’ve wiped off the drips from the liner glazes & cleaned the rims of the mugs. Next I’ll add some wadding to the bottoms and they’ll be ready for loading into the soda kiln… my “Plan B” in case my Soda-Firing Workshop students don’t have enough work to fill the kiln tonight when we load in class later tonight. If these don’t make it in… there’s always my next soda kiln… one step ahead…

Getting ready for soda-firing, so I’m not glazing the exterior of the mugs. The soda kiln atmosphere will do most of the work by adding some shiny glaze surfaces, flashing marks & will also make the colored flashing slips pop in color! But I do glaze the interior of each mug… this time with a simple tenmoku glaze to “visually connect” with the color inside the stamps.

Wiped clean with the tenmoku glaze staying inside the stamped impressions. Next up… liner glazing…

After adding a layer of tenmoku glaze over & into the stamped textures, I gently wipe away the “top layer” to reveal the glaze inlaid in the impressions. It also really helps “pop” the dab of colored flashing slip in the middle of each stamp… details matter!

Getting ready for tonight’s SODA-FIRING WORKSHOP at Lillstreet. My students will be bringing their own bisque to glaze, wad & load tonight. I am glazing up some of my own work as “kiln filler” in case they don’t have enough work to fill the kiln. It’s always tough to estimate the amount of work going into the kiln load. Some of my workshop students have never soda-fired or even been to Lillstreet before… so it will be an interesting mix tonight, and I just want to have a back-up plan ready in case they don’t bring enough work!!!

Did a little quick stamping on this platter tonight. Kinda minimal… not the full blown stamped flange. This platter has a gentle, smooth curve all the way through. So I decided to do a single “simple” border pattern around the rim. Kinda hoping that when it gets glazed, maybe some of the glaze will run and create some cool rivulets coming down from each stamped points?!

So Ive been working on some more of my “handbuilt-wheeltrown-combo” mugs. The bottoms are wheelthrown, the sides handbuilt, and then trimmed & refined on the wheel again! One of my favorite “tricks” for making fun textured mugs!

I start by making some textured slabs of clay. Sometimes with my own stamps, texture mats, or carved rolling pins… like this great one from STODOLA!!! They make tons of different rolling pin textures… including custom designs if you need that. Check ’em out at www.stodola.org.

After pressing in a texture, I cut them into straight-sided rectangles… long enough to be the circumference around the base of the cup.

I throw little “bases” on the wheel… just a small little disc wheelthrown on a plastic bat. I do NOT wire them off as I will be putting them back on the wheel to continue to the process and I want them to stay centered.

I start assembling them by wrapping the slab around the base – scoring & slipping along the way. One of the benefits of this technique is that the weight of the slab is supported by resting on the plastic bat. The extra part below the wheelthrown bottom will be trimmed off later. But it makes a great support system at this point.

Where the slab overlaps, I cut it on an angle and then connect that seam… trying to blend it together as best I can without ruining the pattern. A good “secure” seam is pretty important here.

After attaching the sides, you can spin them on the wheel and press outwards from the inside to give the cup a little curve & volume. I also give the rim a little extra attention to keep it round & smooth… like a wheelthrown cup.

I let the cylinders set-up overnight before trimming… under plastic so they dry slowly to leatherhard. At this point, they can be wired off the plastic bat.

I start by cutting off the excess slab that is “under” where the slab attaches to the wheelthrown disc with a sharp blade. Confusing a bit… as it is now “above” the connection point as the cup has been flipped for trimming.

Then I start trimming the bottom as though it were a “normal” wheelthrown cup. The Giffin Grip helps hold everything in place and centers things quickly! And my DiamondCore Trimming Tools work great for trimming a clan, crisp footring. I make sure to trim all the way into the textured slab so that it blends together and looks seamless.

Once trimmed, I let them sit under plastic while I pull some handles for them. Cups are cups… but a mug needs a handle!!!

So when the handles stiffen-up a bit, I start attaching them to the sides… usually where the seam is as a little “creative camouflage.”

I let the mugs sit under plastic overnight again so that they stiffen-up to leatherhard and the moisture levels balance out. Since these are going to be soda-fired, I decided to dip them in thin colored flashing slips. I held them by the footring and carefully submerged them into the slip to only cover the textured slab sides. I left the curved wheelthrown bottoms as raw clay. I think that the difference will look cool after soda-firing! As the slip was dripping wet after dipping, I propped them up on kiln posts so the dripping would stop before flipping them back over. I didn’t want big drippy runs going down the sides.

So now they’re drying and getting ready for a bisque firing. Once fired, I will add a liner glaze and maybe some other colored glaze accents. After soda-firing, the textures should pop nicely and the flashing slips will help accentuate the pattern.

Finger crossed.

Here’s my February entry in the 2021 Chain Challenge set-up by my talented metalsmith friend Sarah Chapman. Sure, it may not be traditional “links” like a metalsmith’s chain might be… but I think this still works! It’s a 36″ necklace chain of soda-fired beads, turquoise rondelles & copper wire.

It’s the last day of February… so I’ve got to finish my February Chain Challenge piece quickly! You know I “appreciate” a good deadline!!! Sure. I’ve had a month to get this done… but why not start it today?!!!